Custom Glock Parts


Tuned 4.5 Glock Connector....................... $38.95

This 4.5 (previously named 3.5) OEM Minus Glock connector has been tuned for a light, crisp break and reset. All the factory stampings have been removed and polished for a smoother trigger pull over the stock part. This factory Glock connector can be used for GSSF events. Fits all Glock models except G42, G43. Note: These connectors are not used in the Classic Trigger Kits.

Buy Tuned Connector

Custom Firing Pin Safety......................... $35.95

The firing pin safety has been modified from the factory to help eliminate the firing pin from hitting the safety and still function the way it was intended to do. Plus, all the factory edges have been reworked and polished for a smoother trigger pull.Note: Does not fit G42 / G43.

  • Excludes G42 / G43
Buy Firing Pin Safety

Trigger Housing with Over-Travel Stop........ $25.95

Gen 1-3 Trigger Housing Pictured

Generations 1 - 4 - G42 - G43 Trigger Housing! The adjustable over-travel stop is preset when shipped and loctitied even though the setscrew has been installed in a way that it will not move under recoil, but can be fine tuned to your preference with the furnished hex wrench. The setscrew has been milled and polished on the end where the trigger bar hits for a smoother action.

Buy Over Travel Stop Trigger Housing

Trigger Housing with Pre-Travel and Over-Travel Stops....$35.95

Gen 1-3 Trigger Housing Pictured

Generations 1 - 4 Trigger Housing! This part does not have pre-travel removed when shipped. It comes with a furnished hex wrench for the setscrew installed in the trigger housing that allows you to adjust the pre-travel distance. The adjustable over-travel stop is preset when shipped and loc-tited even though the setscrew has been installed in a way that it will not move under recoil, but can be fine tuned to your preference with the furnished hex wrench. The setscrew has been milled and polished on the end where the trigger bar hits for a smoother action. Disclaimer: When removing the pre-travel, the installer must be knowledgeable regarding the safeties function, and it is their responsibility to keep the safety's working properly.

  • Generation 1, 2, and 3 use the same Trigger Housing
  • SF models use the same Trigger Housing as the Gen 4
Buy Gen 1-3 Pre-Over Travel Trigger Housing
Buy Gen 4 Pre-Over Travel Trigger Housing

GEN 5 9mm Custom Trigger Housing with Pre-Travel and Over-Travel Stops....$35.95

Gen5 9mm Trigger Housings Available! This part does not have pre-travel removed when shipped. Gen 5 9mm - It comes with an ejector (marked 30274), trigger spring and hex wrenches for the setscrews installed in the trigger housing, allowing pre-travel and over-travel adjustment. The adjustable over-travel stop is preset when shipped and loc-tited, although the setscrew has been installed in a way that it will not mover under recoil. It can be fine tuned to your preference with the furnished hex wrench. The setscrew has been milled and polisehd on the end where the trigger bar hits for a smoother action. Disclaimer: When removing the pre-travel, the installer must be knowledgeable regarding the safeties function, and it is their responsibility to keep the safeties working properly.

Buy Gen 5 Pre-Over Travel Trigger Housing

GEN 5 Trigger Housing (NO EJECTOR) w/Pre-Travel and Over-Travel Stops... $29.95

Special - Buy Two GEN 5 Trigger Housing (WITH NO EJECTOR) w/Pre-Travel and Over-Travel Stops... $39.95

Gen 5 Trigger Housing (No Ejector) - Use your ejector in my Pre-travel/Over-Travel Stop Trigger Housing. The ejector can be pulled out of your housing with pliers, and then inserted in my custom housing. This part does not have pre-travel removed when shipped. It comes with trigger spring and hex wrenches for the setscrews installed in the trigger housing that allows you to adjust the pre-travel and over-travel. The adjustable over-travel stop is preset when shipped and loc-tited even though the setscrew has been installed in a way that it will not move under recoil, but can be fine tuned to your preference with the furnished hex wrench. The setscrew has been milled and polished on the end where the trigger bar hits for a smoother action. Disclaimer: When removing the pre-travel, the installer must be knowledgeable regarding the safeties function, and it is their responsibility to keep the safeties working properly.

Buy GEN 5 Trigger Housing (NO EJECTOR) w/Pre-Travel and Over-Travel Stops... $29.95

Special - Buy Two GEN 5 Trigger Housing (NO EJECTOR) w/Pre-Travel and Over-Travel Stops... $39.95

$6.00 Flat Rate Shipping on all orders under $100.00